Menu
Cart 0

DynaGen TG350 Genset Controller

  • $325.00


Step up to the New DynaGen TG410 and enjoy some great new features added to the TG350.  DynaGen made it possible to monitor and display current with optional current transformers.   The TG410 also has electronic engine support for standard J1939 Engines (Tier II, III & IV) and a few more you can read about below.

TOUGHSeries

For engines or generators

The TOUGH series controllers are designed to provide complete control, protection and engine instrumentation for both standard and electronic canbus engines, as well as 3-phase volts/amps metering or generator applications. The module is easily configured as either an engine controller or a generator controller using either the front panel buttons or our PC Configurator software. TOUGH series controllers are ideally suited for severe duty applications where reliability is critical such as mobile and stationary engine equipment and generators.

Displays (meets NFPA-110 Level 1):

 

  • Oil Pressure
  • Engine Temperature
  • Fuel Level
  • Oil Level
  • Hour Meter
  • RPM
  • Real time clock display with time/date
  • Battery Voltage
  • J1939 DTC codes with custom text
  • Two customer defined parameters (temperature, pressure, voltage, levels)
  • DPF and DEF status icons
  • 3-Phase AC Volts, Amps and Hz (for generators)

Features and Functions:

 

  • Modbus port with galvanic isolation to connect remote annunciators and internet monitoring devices
  • SAE J1939 CANbus Protocol
  • RPM via J1939, Magnetic pick-up, or Generator
  • Speed control offset adjustment for electronic engines
  • Auto start on Low Battery and other sensors
  • Front panel trim feature for sensor adjustment
  • Maintenance counter
  • Exerciser Clock
  • 150 Event Log
  • Conformally coated for protection against moisture and contaminants
  • Gasket for water ingress protection
  • Free PC Configurator Software
  • Fast and rugged installation clips
  • Passcode protected
  • Automatic shutdowns and warnings
  • Manual and remote start
  • Momentary start/stop inputs
  • Pre-heat and many configurable timers
  • Accepts common senders (VDO, Datcon, Murphy, and more)
  • Custom senders configurable with PC software
  • 5-year warranty

Snap-on RelayPak Option

The RelayPak is socketed to accept four industry standard cube relays. When installed, the RelayPak (RP-100*) eliminates the need to mount and wire external slave relays for Fuel, Crank, and up to two other loads.

* RP-100 includes mounting pack and 3X40 A (resistive) UL pilot duty rated relays

 

DynaGen Tough Series Generator Controller - Snap-on Relay Pac Option

 

 

Front Panel or PC Configurable

The TOUGH series can be programmed manually via front panel buttons or with our easy-to-use PC configurator software that provides customization of screen messages, sender selections, control settings, and much more. The PC configurator uses a standard USB cable with no special programmer required.

 

 

Operating Voltage

  • 5.5 to 38VDC continuous. Cranking dropouts to 0VDC for 50mS, also meets SAE J1113-11
  • Standby Current Draw: 60mA @ 12VDC, 38mA @ 24VDC
  • Reverse battery protected
  • Surge withstand & Load Dump: SAE J1113-11

Operating Temperature

  • Controller Function: -40 to +70˚C
  • Display Screen Viewing: -20 to +70˚C

Vibration & Shock

  • Meets or exceeds SAE J1455

Electromagnetic Compatibility

  • Meets or exceeds MIL-STD-461E 
    Conducted Emissions

Physical

  • Dimensions: 4.17”H x 6.5”W x 1.38”D
  • Weight: 0.83 lb

Speed Sensing

  • Via J1939 bus, Magnetic pick-up, or Generator

Inputs

  • AC Voltage Sensing (inputs for auto selection)
    • Single-phase 2 and 3-wire
    • Delta 3 and 4-wire
    • Wye 2, 3, and 4-wire
    • Max 600vac* (direct connection)
      true RMS, +/- 1% of full scale
  • Current Sensing
    • Accepts 5A Secondary CTs
    • +/- 2% of full scale
  • Fixed Sensor Inputs:
    • 0-7500Ω Engine Temperature sender
    • 0-750Ω Senders or switches**
  • Universal Sensor Inputs (Pressure, Temperature, Level, Volts or Amps.):
    • 0-7500Ω Senders, 4-20ma, 0-5V or switch**
    • 0-750Ω Senders

*for 600vac systems use a step-down transformer or centre tap.

  • Configurable Switched Inputs with programmble text
    • Auto detect close to +Bat or Gnd

Electronic Engine Support:

  • Standard J1939 Engines (Tier II, III & IV)
  • Support for Volvo, John Deere, Cummins, GM PSI, Yanmar, ISUZU*

*Consult factory for updates.

Outputs (includes fuel/crank)

  • Switched Outputs - 1A Max UL pilot duty:
    • Switched to +Battery
    • Short circuit & overload protected

Communications

  • SAE J1939
    • Tier 2, 3, 4i, and 4f engines
    • Address settings for both the controller and the engine ECM
  • USB
    • PC Configurator Connection
    • High retention socket accepts standard USB cable
  • Modbus
    • RTU slave mode
    • RS 485 port (9600, 19200, 38400, 57600 baud)
    • Galvanic isolation

We Also Recommend